Design and Experimental Validation of a 0.6 m Diameter K-Band CFRS Reflector Antenna for Cube Satellite Applications

Article information

J. Electromagn. Eng. Sci. 2026;26(5):518-528
Publication date (electronic) : 2026 September 30
doi : https://doi.org/10.26866/jees.2026.5.r.387
1Department of Electronics and Information Engineering, Korea Aerospace University, Goyang, Korea
2Interdisciplinary Program in Space Systems Engineering, Korea Aerospace University, Goyang, Korea
3Department of Aeronautical and Astronautical Engineering, Korea Aerospace University, Goyang, Korea
4Microwave and Antenna R&D, LIG Defense&Aerospace, Yongin, Korea
5Mechanical R&D (Satellite System), LIG Defense&Aerospace, Seongnam, Korea
6HSCUBE, Goyang, Korea
*Corresponding Author: Jae-Wook Lee (e-mail: jwlee1@kau.ac.kr)
Received 2025 November 20; Revised 2026 January 15; Accepted 2026 February 5.

Abstract

This paper presents the design, fabrication, and experimental validation of a K-band reflector antenna using a triaxially woven carbon-fiber-reinforced silicone (CFRS) composite for small satellite applications. The CFRS surface was formed by curing a single lamina sheet into a parabolic geometry to optimize electromagnetic performance and structural integrity. To mitigate reflection loss caused by fiber discontinuities at high frequencies, a sealed triaxial woven fabric was employed, improving surface continuity and isotropy. Waveguide-based S-parameter measurements yielded an equivalent electrical conductivity of approximately 3,686 S/m and a reflection loss of about 0.2 dB at 20 GHz. Surface profiling confirmed sub-millimeter surface accuracy, and gain degradation due to surface errors was estimated to be less than 0.1 dB. A 0.6 m parabolic reflector achieved a boresight gain of 37.4 dBi at 20 GHz, showing close agreement with full-wave simulations incorporating the measured material and geometric properties. While a conceptual umbrella-type structure was designed to assess mechanical feasibility, the experimental prototype was constructed with a fixed feed support to prioritize precise electromagnetic verification under ground-based conditions. This work provides an experimental foundation for the development of lightweight CFRS-based reflector antennas for future small satellites in low earth orbit.

I. Introduction

Space-based signals intelligence (SIGINT) satellite systems have long been regarded as strategic assets and have predominantly been developed under government-led programs. These systems typically involve the deployment of large satellites in geostationary orbit (GEO) to collect a wide range of communication and electromagnetic signals. A prominent example is the U.S. Orion/Mentor series, which employs large metal-mesh antennas designed to detect extremely weak signals, forming a class of high-cost, high-precision systems [1]. Similar approaches have been pursued by other major spacefaring nations, including Russia (Lotos-S), China (Yaogan series), and France (CERES) [1, 2]. These countries possess the economic and technological capabilities to continuously develop and launch large, high-performance satellites, making them among the few able to operate such high-cost strategic assets. As a result, GEO-based large scale SIGINT satellites remain accessible only to a limited number of nations, and are not a viable option for most countries or organizations due to their prohibitive development and operational costs.

In contrast, the focus of space development has recently been shifted toward the private sector, leading to increased attention on low-cost approaches centered on small satellites operating in low earth orbit (LEO) [3]. This shift is also reflected in the SIGINT domain, where privately led, LEO-based satellite constellations, such as HawkEye 360, are emerging as viable alternatives. These systems leverage multiple CubeSats to achieve rapid revisit times and global coverage, representing a new model for distributed signal intelligence collection [4, 5].

LEO-based small satellite systems are subject to extremely stringent constraints in mass and volume, making the direct application of large mesh antennas and complex deployment mechanisms, commonly used in traditional GEO satellites, highly impractical. In particular, small platforms such as CubeSats cannot accommodate the size, power requirements, or mechanical complexity associated with conventional deployable reflectors, highlighting the need for structural simplification and material innovation.

To address these limitations, this paper proposes a deployable reflector structure utilizing carbon-fiber-reinforced silicone (CFRS), a composite material that inherently combines structural stiffness with elastic shape recovery. This material offers flexibility and elastic recovery properties, enabling simplified deployment mechanisms while maintaining the surface accuracy required for high-frequency antenna applications.

Conventional materials used in deployable reflectors present opposing limitations. Carbon-fiber-reinforced plastics (CFRP) offer high stiffness and dimensional stability, making them suitable for forming precise curved surfaces. However, their inherent lack of flexibility limits mechanical simplification during deployment, and their application in small satellite environments is constrained by limited volume and the complexity of deployment mechanisms. In contrast, metal-mesh reflectors are highly flexible, allowing compact stowage and miniaturization, but they suffer from very low structural rigidity. As a result, they require an increased number of gores and complex cable networks with tensioning systems to maintain their shape [6, 7].

Against this backdrop, CFRS has gained attention as a composite capable of simultaneously providing flexibility and structural rigidity. By combining a triaxially woven carbon fiber fabric with a silicone matrix, CFRS offers elastic shape recovery, thermoelastic stability, and sufficient mechanical support. These properties enable the reflector surface to maintain its parabolic geometry after deployment without the need for complex hinges or actuators. According to Kueh and Pellegrino [8], CFRS retains sufficient elastic recovery even under thermomechanical loading, making it well suited for space structures. Datashvili and Baier [9] further demonstrated the feasibility of implementing self-supporting, high-precision reflector designs using CFRS.

Our research group has previously investigated the structural design and fabrication feasibility of deployable reflector antennas for small satellites using CFRS [10, 11], with a focus on mechanical stability and repeatable deployment reliability at 10 GHz. Building upon this foundation, the present study extends the operational frequency to 20 GHz and performs material and structural optimization to enhance high-frequency reflectivity. In particular, T700 12k carbon fibers with improved electrical conductivity were adopted, and a fully sealed triaxially woven fabric (TWF) configuration was introduced to eliminate fiber gaps, thereby significantly improving surface continuity and electromagnetic compatibility at high frequencies. This revised material configuration was experimentally validated to perform effectively in the targeted frequency range. In addition, the geometry and placement of the feed antenna were optimized in accordance with the reflector’s radiation characteristics to maximize system efficiency. Overall, this work aims to demonstrate the feasibility of a deployable high-gain antenna system for small SIGINT satellites by integrating and refining the CFRS structural concept, its electromagnetic properties, and the feed design.

Based on the technical background and problem context, this paper investigates the structural and electromagnetic feasibility of a CFRS reflector antenna through the following organization. Section II provides a quantitative analysis of the electromagnetic characteristics of the CFRS composite and evaluates its suitability as a reflector material for 20 GHz-class high-frequency antennas. Previous studies [10, 11] employed CFRS with T300 1k carbon fibers, but performance degradation was observed in the higher K-band due to fiber discontinuities and low conductivity. To address this limitation, this study adopts T700 12k carbon fibers and implements a sealed TWF configuration to mitigate fiber gaps. The CFRS was characterized using WR-51 waveguide contact S-parameter measurements with thru-reflect-line (TRL) calibration over 18.5–22 GHz, and reproducibility was checked using three independently fabricated specimens. The surface accuracy of the fabricated reflector was also evaluated through 3D surface profiling, and Ruze’s gain degradation model [12] was applied to estimate the impact of surface errors on antenna performance.

Section III presents the implementation and electromagnetic evaluation of a 0.6 m CFRS parabolic reflector antenna for K-band operation. While an umbrella-type concept was introduced for mechanical feasibility, a simple rib/hinge deployment demonstrator was additionally prepared to provide minimum-level feasibility evidence. The antenna was measured using planar near-field scanning over 18.5–22 GHz, and the resulting far-field patterns were compared with full-wave simulations. To reflect the as-assembled condition, a feed alignment tolerance (±3 mm) was incorporated via tolerance-aware analysis when interpreting measurement–simulation differences. Finally, Section IV summarizes the key findings and discusses limitations and future work.

II. Loss Mechanisms in CFRS Composite

1. Application of T700 12k Triaxial Woven CFRS Composite

CFRS has been considered a promising candidate material for deployable reflector structures due to its ability to simultaneously provide flexibility and structural rigidity. In particular, for small satellite applications, where lightweight and simple deployment mechanisms are essential, along with high-frequency electromagnetic performance, an optimized CFRS structure, beyond a basic composite, is required in terms of both material selection and structural design. In our previous studies [10, 11], we experimentally demonstrated the feasibility of structural implementation of deployable reflectors using CFRS, as well as the ability to maintain surface stability. These studies focused on a CFRS reflector design based on a single lamina configuration operating at 10 GHz, providing practical validation of the mechanical performance and structural applicability of CFRS. However, the CFRS used in those studies, which incorporated T300 1k carbon fibers, exhibited significant reflection loss at higher frequencies. As shown in Fig. 1, the triaxial weave introduced visible fiber gaps, forming aperture-like openings on the surface. As frequency increases, these openings lead to stronger field coupling through the surface, resulting in increased transmission and higher reflection loss. This frequency-dependent increase in reflection loss is confirmed by the measurements presented in Section II-2. Accordingly, the increased reflection loss indicates a reduced equivalent electrical conductivity. This behavior can degrade the reflector performance above 20 GHz.

Fig. 1

Geometry of the CFRS specimen based on T300 1k TWF [10, 11].

To improve reflectivity in the high-frequency band, this study employs a fully sealed TWF structure based on highly conductive T700 12k carbon fibers, with the weave designed to eliminate any fiber gaps. As illustrated in Fig. 2, the TWF consists of 12,000 uniformly arranged fibers in the X, Y, and Z directions, minimizing anisotropy in surface conductivity and enhancing electromagnetic uniformity as a high-frequency reflector. In this work, a CFRS lamina is developed using the T700 12k TWF. SYLGARD 184 was used as the curing agent, and the lamina was sealed in a vacuum bag prior to autoclave curing. The lamina was then cured in an autoclave at 100 °C under an external pressure of 7 bar for 60 min, resulting in a single-ply thickness of approximately 0.2 mm. The CFRS material obtained under this process condition provides sufficient structural stiffness and dimensional stability with a single lamina and is therefore well suited for lightweight and simplified reflector designs without the need for complex multilayer fabrication.

Fig. 2

Geometry of the CFRS specimen based on T700 12k TWF.

2. Reflection Loss and Equivalent Electrical Conductivity of CFRS

CFRS is a composite material that simultaneously offers the flexibility and structural support required for deployable reflector structures. In our previous studies [10, 11], we conducted an initial evaluation of a CFRS reflector antenna operating at 10 GHz, focusing on its structural feasibility, mechanical stability, and fundamental electromagnetic properties, including reflection loss and equivalent electrical conductivity. The specimen used in those studies was a triaxially woven CFRS composite based on T300 1k carbon fibers, which is also used as the reference sample in this work. However, the structure exhibited a sharp increase in reflection loss and a decrease in conductivity at 20 GHz, indicating limitations in its applicability for high-frequency reflector antenna systems.

In response, this study fabricated a CFRS composite optimized for high-frequency applications by employing T700 12k carbon fibers with superior electrical conductivity and a dense TWF structure designed to eliminate fiber gaps. The geometries of the fabricated specimens are shown in Figs. 1 and 2, and both the T300 1k and T700 12k samples were manufactured using the same weaving architecture and resin system. For the T700 CFRS, three independently fabricated specimens were manufactured using the identical process and measured separately to verify fabrication reproducibility, whereas the T300 CFRS specimen was the same as that used in prior studies [10, 11].

The electrical properties were evaluated in terms of equivalent electrical conductivity and reflection loss. Measurements were conducted using a Keysight N5230A vector network analyzer with a waveguide contact setup. As shown in Fig. 3, a WR-51 waveguide, which closely represents the operational band of the target antenna, was used, and calibration was performed via the TRL method to extract the material properties with high accuracy.

Fig. 3

Measurement setup for S-parameter characterization of the CFRS specimens.

The test specimens consisted of triaxial woven CFRS composites with T300 1k and T700 12k configurations. Each CFRS sample was precisely aligned and mounted on the waveguide aperture to measure the reflection coefficient (S11). Measurements were carried out for two orthogonal polarization orientations (0° and 90°), allowing for quantitative analysis of the polarization sensitivity associated with the woven structure. In addition, to assess in-plane uniformity, S11 was measured at 12 segmented positions across each specimen surface by repositioning the waveguide contact location, and the resulting variation was analyzed as standard deviation.

The measured S11 values were then converted to equivalent electrical conductivity σ based on transmission line theory, using the following expression:

(1) σ=4πμ0f(1-∣S11∣2)2Zw2[(1+∣S11∣2)-∣S11∣4+ 6∣S11∣2-1]2

Here, Zw denotes the characteristic impedance of the waveguide, and the surface impedance Zs is defined as follows:

(2) Zs=(1+j)πμ0fσ

The calculated Zs is then converted into reflection loss by comparison with the free space impedance Z0 =377 Ω, according to the following relation:

(3) Reflection Loss=Zs-Z0Zs+Z0

The measurement results are summarized in Fig. 4. As shown in Fig. 4(a), the equivalent electrical conductivity of the T300 CFRS specimen remains below 1,000 S/m across the measured frequency range, exhibiting minimal variation with frequency.

Fig. 4

Measured electromagnetic properties of the CFRS specimens: (a) equivalent electrical conductivity and (b) reflection loss.

In contrast, the T700 CFRS exhibits a mean conductivity between 3,000 S/m and 4,000 S/m, with a mean value of approximately 3,686 S/m at 20 GHz. For the T700 CFRS, the reported conductivity is presented as the mean value obtained from repeated measurements. The corresponding standard deviation is included in Fig. 4(a), and the standard deviation varies in the order of ±148 S/m.

The reflection loss results shown in Fig. 4(b) exhibit a consistent trend. The T300 CFRS shows increasing reflection loss with frequency, reaching approximately 0.7 dB near 20 GHz. In contrast, the T700 CFRS maintains a lower mean reflection loss of around 0.2 dB. The standard deviation of the reflection loss for the T700 CFRS, evaluated from the same repeated measurements, is included in Fig. 4(b) and varies on the order of ±0.0045 dB. These results clearly demonstrate the difference in conductive properties between the two CFRS configurations, indicating that the T700 CFRS is more suitable for achieving stable high-frequency performance. Notably, both specimens exhibited negligible differences between the two polarization orientations (0° and 90°), confirming that the triaxial weave structure is effective in ensuring quasi-isotropic electromagnetic behavior.

These comparative results clearly highlight the limitations of the T300 CFRS used in prior studies and provide experimental evidence that T700 CFRS is a more suitable candidate for high-frequency reflector antenna applications.

3. Gain Analysis

The surface accuracy of a reflector antenna is a critical factor that directly affects its gain performance. In this study, the surface error of the CFRS reflector was measured using a 3D optical scanner (ARAMIS). Based on prior work [10], the RMS surface error of the T300 1k specimen was reported to be 0.17 mm, which corresponds to approximately λ/88 at 20 GHz (λ=15 mm).

To quantitatively evaluate the impact of surface error on gain, the Ruze model [12, 13] was applied. The loss function proposed by Ruze is expressed as follows:

(4) ΔG≈10log10 (e-(4πσrmsλ)2)   (dB)

Here, σrms denotes the RMS surface error of the reflector, and λ is the wavelength corresponding to the operating frequency. The results obtained by applying (4) over the 18–22 GHz frequency range are shown in Fig. 5, with the gain degradation at 20 GHz calculated to be approximately 0.09 dB.

Fig. 5

Gain loss due to surface error versus frequency.

In satellite communication environments, atmospheric attenuation is generally known to be significantly greater than the gain loss caused by surface error [14]. For typical LEO satellite-to-ground links, atmospheric losses due to weather conditions, particularly water vapor and precipitation, can often reach several decibels. Therefore, the 0.09 dB gain degradation resulting from surface error is negligible compared to atmospheric attenuation and is not expected to have a dominant impact on the overall link budget.

In conclusion, the gain loss due to CFRS reflector surface error (0.09 dB) is minor in the context of satellite link budget design. This result suggests that the measured surface accuracy can serve as a valid material design parameter for future reflector antenna and satellite system development.

III. Fabrication and Performance Evaluation of the Reflector Antenna

1. Umbrella-Type Deployable Reflector Configuration

To meet the requirements of compactness and high-frequency performance in small satellite missions, a deployable reflector structure was conceptually designed in this study. A parabolic profile with a diameter of 600 mm and a focal length of 200 mm (F/D=0.33) was defined as the target reflector geometry, based on antenna gain and focusing criteria suitable for 20 GHz operation. This geometric specification also served as the reference shape for the fixed reflector fabricated and tested in later stages of the study. In this section, the deployable configuration and its packaging dimensions are presented to assess the practicality of realizing the target shape with minimal mechanical complexity.

As illustrated in Fig. 6, the proposed configuration adopts an umbrella-type structure composed of six curved radial ribs and a single-lamina CFRS reflective surface. Fig. 6 presents the CAD models of both the deployed and stowed configurations together with their outer dimensions. In the deployed state, the target reflector geometry is a 600 mm-diameter paraboloid (F/D=0.33), while the stowed configuration has an outer envelope of 0.13 m in diameter and 0.34 m in height. In the stowed state, the ribs are folded along the central axis, and upon deployment, the CFRS surface conforms to the curvature defined by the supporting ribs. Using the outer envelope dimensions from the CAD model, the stowed configuration represents a volume reduction of approximately 4.57 times.

Fig. 6

Deployable reflector structural configuration.

In addition, a prototype of the deployable structure shown in Fig. 6 was fabricated using aluminum, and the CFRS surface was mounted on the rib assembly. Fig. 7 shows the deployment process from the folded state to the fully deployed configuration. The CFRS surface can be folded compactly with the rib structure due to its flexibility, while its elastic recovery supports surface conformity to the intended curved geometry in the deployed state.

Fig. 7

Deployment demonstration of the CFRS reflector prototype.

With the proposed rib layout, a single-lamina CFRS surface is intended to form a continuous curved reflector profile across the aperture, including the regions between adjacent ribs. Compared with mesh reflector surfaces, which can exhibit locally flattened segments between adjacent supports, the material continuity of CFRS can ensure a smoother continuous curvature and reduce geometric discontinuities, without requiring additional tensioning or cable-based support. For the antenna measurements reported in this paper, the reflector was evaluated in the deployed geometry while being mechanically fixed during the measurement. The electromagnetic performance verification of the fabricated CFRS reflector is presented in Section III-3.

2. Design and Fabrication of the CFRS Reflector Antenna

This section describes the design and fabrication process of a parabolic reflector structure that realizes the geometric parameters defined in the previous section, namely, a diameter of 600 mm, a focal length of 200 mm, and an F/D ratio of 0.33. The reflector surface was fabricated using a single lamina CFRS surface composed of T700 12k triaxially woven carbon fibers, with the aim of achieving high reflectivity at 20 GHz while maintaining low mass and adequate surface accuracy.

The reflector geometry was formed by placing the T700 12k TWF lamina on a precision machined aluminum parabolic mold and applying a curing process. The reflector fabrication followed a procedure similar to that used for the material test coupons, with the additional use of a precision-machined aluminum mold to define the parabolic geometry. This allowed the structure to maintain its parabolic shape without requiring multilayer laminates or tensioning mechanisms. After curing, the feed mounting point was carefully aligned relative to the geometric focus of the reflector.

Next, the fabrication process of the feed antenna, designed to match the reflector geometry, is described. The feed was optimized for operation at 20 GHz; therefore, a horn antenna utilizing the WR-42 waveguide standard was designed. Fig. 8 illustrates the geometry of a typical horn antenna and defines the flare length as a key design parameter. To optimize the horn antenna for use as a feed, simulations were performed with the flare length as a variable. These optimization simulations were conducted using the I-Solver in CST Studio Suite (CST Microwave Studio). Fig. 9 presents the simulated boresight gain as a function of flare length. The results indicate that the maximum boresight gain is achieved at a flare length of 15 mm. Consequently, a flare length of 15 mm was selected for the final design. To ensure the high internal surface quality required for high-frequency operation, the feed horn antenna was fabricated using electrical discharge machining (EDM).

Fig. 8

Geometry of the feed horn antenna and definition of flare length used in the optimization process.

Fig. 9

Simulated boresight gain as a function of flare length (CST simulation results).

To complete the antenna assembly, the feed supporting structure was constructed using standard aluminum framing profiles rather than custom-designed strut assemblies. In this configuration, a feed alignment tolerance of ±3 mm was maintained. The reflector ribs were fixed in the fully deployed state to preserve the intended deployed geometry during assembly.

The rationale for this design choice lies in the specific scope of the prototype, which is intended to experimentally verify the electromagnetic performance of the CFRS composite material under realistic measurement conditions. Consequently, optimization for deployability or stowed volume was intentionally excluded. Instead, as the objective is to verify performance under ground-based laboratory conditions rather than to fabricate a flight model, the design strategy prioritized fabrication efficiency and structural adjustability while ensuring reflector surface integrity.

3. Performance Evaluation of the CFRS Reflector Antenna

The electromagnetic performance of the fabricated CFRS reflector antenna was evaluated primarily in terms of its radiation pattern and gain characteristics at 18.5–22 GHz. Measurements were conducted in the anechoic chamber of the Korea Radio Promotion Association (RAPA), using a planar near-field measurement system capable of high precision scanning.

Fig. 10 shows the measurement setup, and the fabricated antenna mounted on a fixed aluminum frame. Scanning was performed over a 650 mm × 650 mm area in front of the aperture, with a WR-42 waveguide probe located 100 mm from the reflector surface. The measurements were conducted over the 18.5–22 GHz frequency band. Near-field data were post-processed and transformed into far-field radiation patterns. The transformed far-field radiation patterns were analyzed in both the azimuth and elevation planes.

Fig. 10

Fabricated CFRS reflector antenna and near-field measurement set-up: (a) near-field measurement set-up and (b) fabricated antenna mounted on the near-field measurement setup.

The measured results were cross-validated against full-wave simulation results. Simulations were performed in CST Microwave Studio using the I-solver, with the model constructed to represent the reflector geometry as well as the feed horn and supporting structures in detail. In addition, to reflect the as-assembled condition of the reflector antenna, an alignment tolerance of ±3 mm was applied to the feed position, and a corresponding uncertainty analysis was conducted. This approach enabled a direct and consistent cross-comparison between measurement and simulation.

Fig. 11 presents the boresight gain over the 18.5–22 GHz band. As shown in Fig. 11, the measured boresight gain is distributed close to the mean value of the simulation results that incorporate assembly tolerances, and its frequency-dependent variation across the band follows a trend consistent with the simulations. These results indicate that the fabrication and assembly condition of the prototype achieves the intended radiation performance, supporting that stable boresight gain is maintained over the target frequency range.

Fig. 11

Boresight gain versus frequency (18.5–22 GHz).

Fig. 12 shows the far-field radiation patterns at 20 GHz, where Fig. 12(a) and 12(b) correspond to the azimuth and elevation planes, respectively. In both planes, the measured and simulated patterns exhibit overall good agreement in terms of main-lobe shape and sidelobe distribution. At 20 GHz, the measured boresight gain was 37.4 dBi, compared with 39.2 dBi from the ideal simulation; when assembly tolerances were considered, the mean simulated gain was 37.7 dBi, which is in close agreement with the measurement. The measured pattern also remained within the maximum–minimum variation envelope predicted by the tolerance-aware simulations over off-boresight angles. In addition, the beamwidth showed a comparable level between measurement and simulation, confirming that both the beamwidth and sidelobe characteristics are consistently reproduced by the model and the measurement.

Fig. 12

Comparison of measured and simulated radiation patterns of the CFRS reflector antenna at 20 GHz: (a) azimuth plane and (b) elevation plane.

An observation in Fig. 12(b) is that the measured gain pattern exhibits a slight downward tilt of the main-lobe direction. This behavior is expected to result from gravity-sagging structural deformation under the ground-based measurement condition. In principle, compensating for such gravity effects requires an instrumentation configuration using a 0-G antenna pattern measurement fixture. However, the current measurement environment did not allow the application of such a fixture, and thus complete compensation was not feasible. Moreover, implementing a gravity off-loading fixture typically involves nontrivial fabrication and validation efforts, and was therefore not included in the present experimental setup.

Despite this limitation inherent to ground-based measurements, the measured boresight gain and overall pattern characteristics remain in good agreement with the simulation results. This indicates that the T700 CFRS composite adopted in this study experimentally achieves the electrical performance required for high-frequency reflector antenna applications.

IV. Conclusion

A parabolic reflector antenna was fabricated using a single lamina CFRS composite formed from T700 12k triaxially woven fibers. The CFRS lamina was produced by enclosing the triaxial fabric in a sealed vacuum bag and curing it in an autoclave at 100 °C under an external pressure of 7 bar for 60 min, resulting in a single-ply thickness of approximately 0.2 mm. The surface conductivity of the cured sheet was characterized by a waveguide contact S-parameter method over 18.5–22 GHz with TRL calibration and linear polarization (0°, 90°), resulting in an extracted conductivity of σ ≈ 3,686 S/m.

Using this material, a 0.6 m-diameter parabolic reflector with F/D=0.33 was implemented. The reflector follows an umbrella-type deployable mechanism, while in this study the electromagnetic performance was evaluated in the fully deployed and mechanically fixed configuration. A feed alignment tolerance of ±3 mm was taken into account when interpreting the measurement and simulation results. The main fabrication parameters of the T700 12k CFRS, the material characterization settings, and the reflector geometry and deployment related conditions are summarized in Table 1.

Fabrication parameters of the T700 12k CFRS

Near-field measurements of the fabricated reflector showed a boresight gain of 37.4 dBi and cross-polarization levels below −30 dB, which are in reasonable agreement with full-wave simulations that use the measured surface conductivity.

Future work will investigate the design and implementation of a hat-fed antenna system to fundamentally address the feed blockage issue. Unlike the current setup, the hat-fed configuration employs a self-supporting mechanism that eliminates the need for supporting structure, thereby maximizing aperture efficiency. Furthermore, to mitigate the gravitational deformation observed in this study, a gravity-compensated measurement setup will be developed. This advanced testing environment is intended to minimize surface distortion, allowing for precise experimental verification of the deployable reflector's performance under conditions representative of the space environment.

Notes

This research is performed based on the cooperation with Korea Aerospace University—LIG Defense&Aerospace Cooperation.

References

1. Han J. W., Lee Y. S., Choi D., Park J., Kim H.. Trend of satellite technologies for signal information acquisition. Journal of Space Technology and Applications 2(4):268–286. 2022;https://doi.org/10.52912/jsta.2022.2.4.268.
2. Clark P. S.. China’s Shiyan Weixing Satellite Programme: 2004–2017. Space Chronicle: A British Interplanetary Society Publication 71(1):22–29. 2018;
3. Brodecki M., de Groot Z.. SIGINT: the mission CubeSats are made for. In : Proceedings of the 32nd Annual AIAA/USU Conference on Small Satellites. Logan, UT, USA; 2018;
4. Sarda K., CaJacob D., Orr N., Zee R.. Making the invisible visible: precision RF emitter geolocation from space by the HawkEye 360 Pathfinder mission. In : Proceedings of the 32nd Annual AIAA/USU Conference on Small Satellites. Logan, UT, USA; 2018;
5. Rahmat-Samii Y., Manohar V., Kovitz J. M.. For satellites, think small, dream big: a review of recent antenna developments for CubeSats. IEEE Antennas and Propagation Magazine 59(2):22–30. 2017;https://doi.org/10.1109/MAP.2017.2655582.
6. Kim J. H., Lee S. A., Park T. Y., Choi H. S., Kim H., Chae B. G., Oh H. U.. Analysis of RF characteristics and effectiveness according to the number of gores in a mesh antenna. Journal of Space Technology and Applications 1(3):364–374. 2021;https://doi.org/10.52912/jsta.2021.1.3.364.
7. Huang J., Yoo Y., Jo S. J., Seo C. W., Lee S. A., Yoon S. S., Park S. O.. Analysis of the characteristics of mesh with complex knitting patterns for spaceborne reflector antennas. Journal of Electromagnetic Engineering and Science 24(6):565–573. 2024;https://doi.org/10.26866/jees.2024.6.r.262.
8. Kueh A. B. H., Pellegrino S.. Thermo-elastic behavior of single ply triaxial woven fabric composites. In : Proceedings of the 47th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference. Newport, RI, USA; 2006; https://doi.org/10.2514/6.2006-1899.
9. Datashvili L., Baier H.. Membranes and thin shells for space reflectors. In : Proceedings of the International Conference on Engineering, Construction, and Operations in Challenging Environment (Earth & Space 2006). Houston, TX, USA; 2006; p. 1–8. https://doi.org/10.1061/40830(188)7.
10. Kang D. S., Keum D. H., Choi J. H., Lee M. H., Park K., Jung H. Y., al et. Flexible surface reflector antenna for small satellites. Aerospace 12(5)article no. 414. 2025;https://doi.org/10.3390/aerospace12050414.
11. Park K., Kang D. S., Jung H. Y., Yu J. W., Cho S. B., Kim J. H., al et. Design and fabrication of a satellite reflector antenna using carbon fiber reinforced silicone (CFRS). The Journal of Korean Institute of Electromagnetic Engineering and Science 36(3):250–253. 2025;https://doi.org/10.5515/KJKIEES.2025.36.3.250.
12. Ruze J.. Antenna tolerance theory—a review. Proceedings of the IEEE 54(4):633–640. 1966;https://doi.org/10.1109/PROC.1966.4784.
13. Kiedron K., Chian C. T., Chuang K. L.. Statistical analysis of the 70-meter antenna surface distortions. In : The Telecommunication and Data Acquisition Progress Report 42–88. Pasadena, CA, USA; 1987;
14. Prediction methods required for the design of Earth–space telecommunication systems: Propagation by rain. ITU-R Recommendation P.618–13 2017;https://www.itu.int/rec/R-REC-P.618-13-201712-S/en.

Biography

Kitae Park, https://orcid.org/0009-0003-4548-8599 received his B.S. and M.S. degrees in electronics and information engineering from Korea Aerospace University, Korea, in 2022 and 2023, respectively, where he is currently pursuing a Ph.D. degree. His current research interests include design and analysis of deployable CFRS and mesh reflector antennas for SAR satellites and CubeSats, electromagnetic characterization of advanced materials using improved NRW methods, optimization-based dielectric lens design, and neural network-based electromagnetic protection performance prediction.

Dong-Hun Keum, https://orcid.org/0009-0001-6970-9064 received the B.S. and M.S. degrees in aeronautical and astronautical engineering from Korea Aerospace University, Goyang, Republic of Korea, in 2025 and 2026, respectively. Since 2026, he has been with Hanwha Aerospace, Daejeon, Republic of Korea, where he is currently a Research Engineer. His research interests include structural design and analysis of aerospace systems, deployable space structures, reflector antenna engineering for small satellites, multiphysics-based performance evaluation of spaceborne components, and optimization techniques for aerospace applications.

Sang-Joon Oh, https://orcid.org/0009-0008-7304-1459 received his B.S. and M.S. degrees in aeronautical and astronautical engineering from Korea Aerospace University, Republic of Korea, in 2024 and 2026, respectively. His research interests include deployable space structures, multibody dynamics, reflector antenna engineering for small satellites, and the structural design and analysis of deployable truss booms for large mesh reflector antennas.

Soo-Bean Cho, https://orcid.org/0000-0002-1675-8065 received the B.S. and M.S. degrees in electronic engineering from Sejong University, Seoul, South Korea, in 2016 and 2019, respectively. Since 2022, she has been with LIG Defense&Aerospace, where she is currently a Research Engineer. Her research interests include reflectarray antennas, active phased array antennas, radar and imaging radar systems, and microwave systems.

Je-Woo Yu, https://orcid.org/0000-0003-1204-074X received the B.S. degree in information and communication engineering from Chungnam National University, Daejeon, South Korea, in 2005, and the M.S. degree in radio science and engineering from Chungnam National University, Daejeon, South Korea, in 2008. Since 2008, he has been with LIG Defense&Aerospace, where he is currently a Chief Research Engineer. His main research interests include radar and imaging radar systems, and microwave systems.

Heeduck Chae, https://orcid.org/0000-0003-4609-1764 received his B.S., M.S., and Ph.D. degrees in electrical and computer engineering from Seoul National University, Seoul, South Korea, in 1999, 2001, and 2008, respectively. Since March 2007, he has been with LIG Defense&Aerospace, where he is currently a Team Leader. His research interests include active phased array antenna systems, radar systems, microwave passive circuit design, and computational electromagnetics.

Hwa-Young Jung, https://orcid.org/0000-0002-5366-4527 received his M.S. degree in mechanical engineering from Hanyang University in 2002. He is currently Team leader of Mechanical R&D Satellite System department at LIG Defense&Aerospace. His research interests include structural dynamics and deployable antenna structures.

Jin-Ho Roh, https://orcid.org/0000-0002-4496-1490 received his Ph.D. in Aerospace Engineering from the Korea Advanced Institute of Science and Technology (KAIST), Daejeon, South Korea, in 2006. He is currently a Professor in the Department of Aeronautical and Astronautical Engineering at Korea Aerospace University, Goyang, South Korea, where he serves as the Director of the Space Structures Laboratory. He is also the CEO of HSCUBE (www.hscube.co.kr), a startup company focused on the research and development of deployable antenna systems for space applications. He has published more than 50 papers in international journals on the analysis, design, and manufacturing of deployable space structures. His current research interests include the development of deployable space structures for small satellite missions.

Jae-Wook Lee, https://orcid.org/0000-0003-2903-5904 received the B.S. degree in electronic engineering from Hanyang University, Seoul, South Korea, in 1992, and the M.S. and Ph.D. degrees in electrical engineering with a specialization in electromagnetics from the Korea Advanced Institute of Science and Technology, Daejeon, South Korea, in 1994 and 1998, respectively. From 1998 to 2004, he was a senior member of Advanced Radio Technology Department, Radio and Broadcasting Research Laboratory, Electronics and Telecommunications Research Institute, Daejeon. Since 2004, he has been with the faculty of the Korea Aerospace University, Goyang, South Korea, where he is currently a Professor with the School of Electronics and Information Engineering. He is also the CEO of HSCUBE (www.hscube.co.kr), a startup company focused on the research and development of deployable antenna systems for space applications. His current research interests include high-power amplifier design, computational electromagnetics, electromagnetic interference/electromagnetic compatibility analysis on printed circuit boards, satellite antennas, and spaceborne SAR systems.

Article information Continued

Funded by : Korea Aerospace University—LIG Defense&Aerospace Cooperation
Funding : This research is performed based on the cooperation with Korea Aerospace University—LIG Defense&Aerospace Cooperation.

Fig. 1

Geometry of the CFRS specimen based on T300 1k TWF [10, 11].

Fig. 2

Geometry of the CFRS specimen based on T700 12k TWF.

Fig. 3

Measurement setup for S-parameter characterization of the CFRS specimens.

Fig. 4

Measured electromagnetic properties of the CFRS specimens: (a) equivalent electrical conductivity and (b) reflection loss.

Fig. 5

Gain loss due to surface error versus frequency.

Fig. 6

Deployable reflector structural configuration.

Fig. 7

Deployment demonstration of the CFRS reflector prototype.

Fig. 8

Geometry of the feed horn antenna and definition of flare length used in the optimization process.

Fig. 9

Simulated boresight gain as a function of flare length (CST simulation results).

Fig. 10

Fabricated CFRS reflector antenna and near-field measurement set-up: (a) near-field measurement set-up and (b) fabricated antenna mounted on the near-field measurement setup.

Fig. 11

Boresight gain versus frequency (18.5–22 GHz).

Fig. 12

Comparison of measured and simulated radiation patterns of the CFRS reflector antenna at 20 GHz: (a) azimuth plane and (b) elevation plane.

Table 1

Fabrication parameters of the T700 12k CFRS

Parameter Value
Material fabrication
 Carbon fiber T700 12k Triaxial Woven Fabric
 Cure temperature 100 °C in autoclave
 Cure pressure 7 bar
 Cure hold time 60 min
 Curing agent SYLGARD 184
 Lamina thickness ≈ 0.2 mm
Material electrical characterization
 Measurement method Waveguide contact method
 Material frequency range 18.5–22 GHz
 Waveguide Specification WR-51
 Extracted surface conductivity σ ≈ 3,686 S/m
 Calibration scheme TRL
Reflector geometry/deployment
 Reflector type Parabolic reflector
 Reflector diameter 0.6 m
 F/D ratio 0.33
 Deployment concept Umbrella-type deployable mechanism
 Configuration for EM evaluation Fully deployed and mechanically fixed
 Stowed envelope diameter, height 0.13 m, 0.34 m
 Volume reduction ratio 4.57
 Feed alignment tolerance ±3 mm