J. Electromagn. Eng. Sci Search

CLOSE


J. Electromagn. Eng. Sci > Volume 26(5); 2026 > Article
Cho, Kwon, and Hong: Design of a Wideband Blocking Energy-Selective Surface (ESS) Structure for Defense against High-Power Signals

Abstract

In this paper, an energy-selective surface (ESS) structure operating at 3.5 GHz is designed to protect various communication systems from high-power microwave (HPM) threats. The proposed structure achieves wideband blocking characteristics by stacking a grid pattern with a cross-shaped patch pattern. Simulation results show that the ESS structures provide a pass bandwidth of 1.47 GHz based on a −2 dB at low-power signal and a wideband blocking bandwidth of 15 GHz based on a −15 dB at high-power signal. The proposed unit structure was validated by measuring the received signal strength according to change in incident wave intensity using a waveguide measurement setup. The measurement results confirm that the shielding effectiveness increases when the incident power exceeds 21 dBm. It was confirmed that the proposed ESS structures can actively block high-power signals.

I. Introduction

High-power microwaves (HPMs) are extremely intense electromagnetic waves, typically exceeding 1 GW in power and operating in frequency ranges from several hundred MHz to several hundred GHz. HPMs can cause malfunction or even physical damage to antennas, GPS devices, and other electronic systems to their high intensity. Therefore, protective technologies such as shielding covers are required for communication system [1]. One of the most representative technologies is the frequency-selective surface (FSS), a periodic structure that selectively transmits or blocks specific frequency bands [2, 3].
The FSS structures operate as a spatial filter that selectively passes or blocks signals only in a desired band (in-band). However, incorporating switching elements such as PIN or varactor diodes into the FSS unit cell enables the design of an active frequency- selective surface (AFSS) capable of actively tuning its operating frequency band. While the AFSS structure can block specific frequencies in undesired bands (out-of-band), it does not block the HPM signals effectively. In addition, it requires a complex bias line circuit to operate the switching elements, and it cannot respond actively to sudden high-power incident signals [4, 5]. Recently, research on energy-selective surface (ESS) structures has been actively conducted to protect electronic components from HPM threats [6–12]. Fundamentally, ESS structures are like AFSS structures in that they primarily use switching elements such as PIN diodes. When the incident wave power is low, the PIN diodes remain in the OFF state and low insertion loss is observed within the operating frequency band. In contrast, when the incident wave power is high, current is induced on the surface of the ESS unit cell, causing the PIN diodes to be turned ON. As a result, the signal within the operating frequency band can be effectively blocked.
Previous studies on ESS structures have primarily focused on achieving low insertion loss in the in-band region and broad-band characteristics, with limited attention given to polarization and incident angle stability. In prior works [6–8], a pass-band bandwidth exceeding 1 GHz is observed only under low-power signals, whereas the stop-band bandwidth under high-power signals remains below 8 GHz. Conversely, prior works [9–14] show wide stop-band performance (10–20 GHz) under high-power conditions. But their passband bandwidth under low-power signals remains extremely narrow, typically below 1 GHz or more than four diodes were used.
In this paper, an ESS structure employing PIN diodes is designed, fabricated, and experimentally validated. The proposed structure has a pass-band bandwidth greater than 1 GHz under low-power signal conditions and exhibits a wideband stop-band characteristic exceeding 10 GHz under high-power signals.

II. ESS Unit Cell

In this paper, to design an ESS structure unit cell that allows signal transmission under low-power signal conditions and provides broadband blocking under high-power conditions, it is necessary to develop a band-pass unit cell with wide blocking characteristics. Therefore, a grid structure exhibiting high-pass characteristics is combined with a cross-shaped patch structure providing band-stop characteristics at higher frequencies. As shown in Fig. 1, the proposed design achieves a very low insertion loss of −0.23 dB at the target frequency of 3.5 GHz, while exhibiting wideband blocking characteristics over the remaining frequency bands.
Based on the designed band-pass unit structure, an ESS structure unit cell was designed as shown in Fig. 2. The proposed unit cell consists of an active layer including PIN diodes to achieve switching functionality and a passive layer to enhance frequency selectivity and bandwidth. The active and passive layers are fabricated on an FR4 substrate with a thickness of 0.8 mm (ɛr = 4.4, loss tangent = 0.02), and an air layer with thickness H is placed between them.
In the active layer, the PIN diodes remain in the OFF state under low-power signal conditions, allowing signal transmission. When a high-power signal is incident, it induces a voltage across the PIN diodes, turning them ON and blocking the signal. The PIN diode is modeled as an SMP1345-079LF, and its equivalent circuit representation is illustrated in Fig. 2(c).
Fig. 3 shows the simulated transmission and reflection characteristics of the active layer with an array of PIN diodes. When the PIN diodes are in the OFF state (low-power signal conditions), the ESS structure has a low insertion loss of −0.22 dB at the resonant frequency of 3.46 GHz, with a bandwidth of 0.63 GHz (from 3.14 to 3.77 GHz) based on the −2 dB level. In contrast, under high-power signal conditions, the resonant frequency shifts to 6.47 GHz, and the insertion loss increases slightly to −1.72 dB. By including PIN diodes into the band-pass unit cell, strong attenuation of −20 dB at the operating frequency of 3.5 GHz was achieved under high-power conditions. However, this configuration was found to be insufficient for achieving wideband blocking. To overcome this limitation, an air gap and a passive layer with frequency-selective transmission characteristics were introduced beneath the active layer. Through coupling effects between these layers, broadband blocking characteristics were successfully realized [11].
Fig. 4 presents the simulated transmission characteristics of the proposed ESS structure with the heights H of the varied air layer. Fig. 4(a) and 4(b) show the transmission characteristics for TE and TM polarizations, respectively, under low-power signal conditions. As the height H increases, the operating bandwidth decreases, but the insertion loss is low. When H = 7 mm, the bandwidth reaches 1.47 GHz (3.42–4.89 GHz) at the −2 dB level, which is wider than that of the active layer alone.
Fig. 4(c) and 4(d) show the transmission characteristics under high-power signal conditions for TE and TM polarizations. As the air gap height H increases, an improved the stop bandwidth is observed in the 3–8 GHz range. When H = 7 mm, the ESS structure achieves wideband blocking from 1 to 15 GHz at the −15 dB level. Based on these results, the frequency response with respect to variations in design parameters was analyzed, and the structure was optimized to get stable performance across TE/TM polarizations and incident angles ranging from 0° to 40°. The optimized design parameters are summarized in Table 1.
The simulated transmission characteristics under polarization and incident angle variations for the optimized design parameters are shown in Fig. 5. Under low-power signal conditions, as illustrated in Fig. 5(a), the insertion loss tends to decrease as the incident angle increases. However, the insertion loss remains relatively low across the range of 0°–40°, indicating stable performance. As shown in Fig. 5(b), when a high-power signal is incident, the blocking characteristics are low in a specific high-frequency band from an incident angle of 30° or higher.

III. Fabrication and Measurement

To verify the performance of the proposed ESS structure, the unit cells were arrayed according to the aperture size of the waveguide, as shown in Fig. 6, and the structure was fabricated. Since the pass-band of the ESS structure ranges from 3.4 GHz to 4.74 GHz, WR-284 and WR-187 waveguides were used to cover the full measurement range from 2.65 GHz to 6 GHz. To realize the 7-mm air gap between the top and bottom layers, waveguide holders were fabricated using aluminum with a thickness of 7 mm and employed during the measurement. As shown in Fig. 7, separate measurement setups were configured for low-power and high-power signal conditions to evaluate the transmission characteristics of the fabricated ESS structure. The measurement setup employed an HP 83732A signal generator, an Agilent E4409B spectrum analyzer, and a 15 dBm power amplifier from Aaronia AG, Germany. In addition, isolators and attenuators from A-Info, rated for up to 100 W operation up to 6 GHz, were used to protect the measurement systems. For low-power signal measurements, only a signal generator and a spectrum analyzer were used, since the amplifier used in this study does not operate when the input power is below −5 dBm. For high-power signal measurements, an amplifier was inserted between the signal generator and the ESS structure. To protect the equipment from strong reflected signals at high power, an isolator and an attenuator were additionally connected. As a result, cable losses due to various equipment from the signal generator to the ESS structure occur, so it is necessary to calibrate the cable losses. Using a network analyzer, the frequency-dependent losses of the measurement paths denoted by ⓐ, ⓑ, and ⓒ in Fig. 7 were measured, as listed in Tables 2 and 3. The measured insertion losses were compensated by calibrating the signal generator’s input power at each corresponding frequency.
Fig. 8 shows the measured S21 results obtained using a vector network analyzer (VNA). When a low-power signal is applied (i.e., when the PIN diode is in the OFF state), it shows a similar trend in the target pass-band of 3.4–5 GHz. Measurements under high-power signal conditions are challenging to conduct using a VNA. Therefore, under the assumption that the PIN diode operates in the ON state for high-power excitation, an equivalent resistance of 2 Ω was connected, and the corresponding measurement result is shown in Fig. 8(b). Under high-power signal conditions, the measured transmission characteristics also shows a level higher than −15, consistent with the simulation, confirming high blocking performance.
Fig. 9 shows the measured blocking performance of the ESS when the input power is varied from −20 dBm to 25 dBm using the measurement system of Fig. 7. At the target passband frequencies of 3.5 GHz and 4.6 GHz, the shielding effectiveness (SE) is as low as about 5 dB. When the input power increases to 21 dBm, the SE increases and the blocking effectiveness improved, reaching around 14 dB attenuation at 25 dBm. At the out-of-band frequencies of 2.8 GHz and 6 GHz, the ESS structure shows high attenuation of approximately 16 dB even at low input power levels. When the input power exceeds 21 dBm, the PIN diodes are activated, resulting in an increase in blocking performance to over 20 dB.
Table 4 compares the performance of the proposed unit cell with previously reported ESS structures [6–13] as well as ESA-related studies [15, 16]. Although the proposed unit cell has a relatively larger size compared to some previous works, it achieves a relatively wide passband bandwidth of 1.5 GHz under low-power signal conditions and a wide stopband bandwidth of 15 GHz under high-power signal conditions using only four lumped elements. In addition, the proposed structure provides stability against polarization and incident-angle variations.

IV. Conclusion

In this paper, an ESS structure unit cell was designed to selectively pass the 3.5 GHz band under low-power signal conditions and to provide wideband frequency blocking under high-power signals. Initially, a band-pass unit cell was designed by combining a grid structure and a cross-shaped patch pattern. Then, PIN diodes were placed on the upper layer, followed by stacking an air gap and a passive layer beneath it. This allows for wideband blocking performance when exposed to high-power signals. Simulation results confirmed that the proposed structure has a bandwidth of 1.47 GHz at the −2 dB level under low-power conditions and provides blocking over a 1–15 GHz range at the −15 dB level under high-power conditions. Furthermore, stable frequency response characteristics were observed for polarizations and incident angles ranging from 0° to 40°. To validate the performance of the fabricated unit cell, measurements of received signal strength under normal incidence were conducted using WR-284 and WR-187 waveguides. The measurement results showed good agreement with the simulation. Furthermore, measurements of SE as a function of input power revealed that the PIN diodes activate at approximately 21 dBm, resulting in enhanced blocking performance.

Notes

This work was supported in part by the Priority Research Center Program through the National Research Foundation under Grant RS-2019-NR040074, and in part by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education under Grant RS-2024-00407836, and in part by Institute of Information & communications Technology Planning & Evaluation (IITP) grant funded by the Korea government (MSIT) (No. RS-2025-02642985, Development of Identification, Protection, and Detection Technologies for High-Power Electromagnetic Pulse Protection).

Fig. 1
Design process of a band-pass unit cell with wide blocking characteristics.
jees-2026-5-r-389f1.jpg
Fig. 2
Proposed unit structure of ESS: (a) 3D view, (b) top view, and (c) PIN diode equivalent circuit.
jees-2026-5-r-389f2.jpg
Fig. 3
Simulation results of transmission/reflection characteristics of the active layer: (a) low-power signal incidence and (b) high-power signal incidence.
jees-2026-5-r-389f3.jpg
Fig. 4
Simulation results of transmission characteristics according to variation in air layer heights (H). (a) TE mode and (b) TM mode under low-power signal incidence. (c) TE mode and (d) TM mode under high-power signal incidence.
jees-2026-5-r-389f4.jpg
Fig. 5
Simulation results of transmission characteristics (incidence angles: 0°–40°): (a) Low-power signal incidence and (b) high-power signal incidence.
jees-2026-5-r-389f5.jpg
Fig. 6
Fabricated ESS structure.
jees-2026-5-r-389f6.jpg
Fig. 7
Measurement systems under different conditions: (a) low-power signals (−15 to 10 dBm), (b) high-power signals (12 to 25 dBm), and (c) measurement setup for high-power signals.
jees-2026-5-r-389f7.jpg
Fig. 8
Measurement results of transmission characteristics for fabricated ESS structures: (a) low-power signals and (b) high-power signals.
jees-2026-5-r-389f8.jpg
Fig. 9
Measurement results of SE according to input power strength.
jees-2026-5-r-389f9.jpg
Table 1
Optimized dimension of the ESS unit cell (unit: mm)
Parameter Value Parameter Value
P 15 L1 11
L2 13.5 W1 1.5
W2 3 W3 0.25
W4 4 G1 0.5
G2 0.25 h1 0.8
H 7 – –
Table 2
Loss compensation values for each frequency at low-power signal conditions
Low-power (GHz) ⓐ (dB) Loss cal. (dB) Input power (dBm)
3 −0.2 0.2 −19.8–10
3.5 −0.3 0.3 −19.7–10.2
4.0 −0.36 0.36 −19.64–10.36
4.5 −0.4 0.4 −19.6–10.4
5.0 −0.43 0.43 −19.57–10.43
5.5 −0.44 0.44 −19.56–10.44
6 −0.45 0.45 −19.55–10.45
Table 3
Loss compensation values for each frequency at high-power signal conditions
High-power (GHz) ⓐ (dB) ⓑ (dB) ⓒ (dB) Loss cal. (dB) Input power (dBm)
3 −0.2 −0.8 −0.32 1.32 −1.68–11.32
3.5 −0.3 −0.85 −0.35 1.5 −1.5–11.5
4.0 −0.36 −0.88 −0.38 1.62 −1.38–11.62
4.5 −0.4 −0.9 −0.41 1.71 −1.29–11.71
5.0 −0.43 −0.94 −0.45 1.82 −1.18–11.82
5.5 −0.44 −0.97 −0.49 1.9 −1.1–11.9
6 −0.45 −1.0 −0.5 1.95 −1.05–11.95
Table 4
Performance comparison of ESS
Study Type Unit cell Element (ea) BW (GHz) Stability (°) Max SE (Sim.) (dB)

Low-power High-power
Hu et al. [6] ESS 0.15λ 2 2.5 4 - 30
Hu et al. [7] ESS 0.17λ 9 1.5 3 - 21
Wu et al. [8] ESS 0.2λ 10 3 8.5 - 22
Qin et al. [9] ESS 0.16λ 4 0.8 20 - 17.5
Gong et al. [10] ESS 0.17λ 12 0.5 13 0–40 14
Wu et al. [11] ESS 0.16λ 52 9.4 14 0–60 25
Jiang et al. [12] ESS 0.12λ 8 0.5 10.7 0–60 30
Zhou et al. [13] ESS 0.1λ 8 3.2 10 0–55 22
Gai et al. [15] ESA 0.24λ 4 0.1 0.1 Co/Cross-pol 12
Zha et al. [16] F-AMC 0.31λ 2 1.4 0.7 0–60 20
Proposed ESS 0.21λ 4 1.5 15 0–40 28

References

1. D. V. Giri and F. M. Tesche, "Classification of intentional electromagnetic interference (IEMI)," IEEE Transactions on Electromagnetic Compatibility, vol. 46, no. 3, pp. 322–329, 2004. https://doi.org/10.1109/TEMC.2004.831819
crossref
2. J. H. Jin, "GPS system research for high-power electromagnetic wave protection," Ph.D. dissertation, Kumoh National Institute of Technology. Gumi, Republic of Korea, 2017.

3. F. Costa, A. Monorchio, and G. Manara, "Efficient analysis of frequency-selective surfaces by a simple equivalent-circuit model," IEEE Antennas and Propagation Magazine, vol. 54, no. 4, pp. 35–48, 2012. https://doi.org/10.1109/MAP.2012.6309153
crossref
4. P. M. Sainadh and S. Ghosh, "A multifunctional reconfigurable frequency-selective surface with simultaneous switching and tuning capability," IEEE Transactions on Antennas and Propagation, vol. 72, no. 10, pp. 7700–7709, 2024. https://doi.org/10.1109/TAP.2024.3448305
crossref
5. L. M. Zhang, X. Ding, and M. Bozzi, "Passband-tunable reconfigurable frequency-selective surface with wide tuning range," IEEE Transactions on Microwave Theory and Techniques, vol. 72, no. 9, pp. 5167–5178, 2024. https://doi.org/10.1109/TMTT.2024.3378979
crossref
6. N. Hu, Y. Zhao, J. Zhang, P. Liu, H. Xu, and F. Costa, "High-performance energy selective surface based on an equivalent circuit design approach," IEEE Transactions on Antennas and Propagation, vol. 70, no. 6, pp. 4526–4538, 2022. https://doi.org/10.1109/TAP.2021.3137293
crossref
7. N. Hu, K. Wang, J. Zhang, S. Zha, Z. Wu, C. Liu, and et al, "Design of ultrawideband energy selective surface for high-power microwave protection," IEEE Antennas and Wireless Propagation Letters, vol. 18, no. 4, pp. 646–650, 2019. https://doi.org/10.1109/LAWP.2019.2900760
crossref
8. Z. Wu, P. Liu, B. Deng, T. Tian, S. Zha, and X. Ni, "An ultrabroadband energy selective surface with nonreciprocal performance for HIRF protection," IEEE Transactions on Electromagnetic Compatibility, vol. 65, no. 4, pp. 1202–1210, 2023. https://doi.org/10.1109/TEMC.2023.3268271
crossref
9. D. Qin, R. Ma, J. Su, X. Chen, R. Yang, and W. Zhang, "Ultra- wideband strong-field protection device based on metasurfaces," IEEE Transactions on Electromagnetic Compatibility, vol. 62, no. 6, pp. 2581–2590, 2020. https://doi.org/10.1109/TEMC.2020.3020840
crossref
10. W. Gong, W. Zhang, X. Chen, G. Han, L. Han, J. Su, and et al, "A low-profile energy selective surface with ultra-wide absorption band," IEEE Transactions on Microwave Theory and Techniques, vol. 71, no. 3, pp. 1348–1355, 2023. https://doi.org/10.1109/TMTT.2022.3222385
crossref
11. Z. Wu, Y. Xu, P. Liu, T. Tian, and M. Lin, "An ultrabroadband energy selective surface design method: from filter circuits to metamaterials," IEEE Transactions on Antennas and Propagation, vol. 71, no. 7, pp. 5865–5873, 2023. https://doi.org/10.1109/TAP.2023.3276447
crossref
12. Y. Jiang, L. Tian, Z. H. Jiang, and W. Hong, "Analysis and design of ultrathin filtering energy-selective surfaces with ultrawideband and high shielding effectiveness," IEEE Transactions on Antennas and Propagation, vol. 73, no. 1, pp. 641–646, 2025. https://doi.org/10.1109/TAP.2024.3464876
crossref
13. T. Zhou, P. Liu, C. Liu, H. Jiang, and T. Tian, "Multilayer energy selective surface with wide operational band and high shielding effectiveness based on second-order filter," IEEE Transactions on Electromagnetic Compatibility, vol. 67, no. 1, pp. 337–340, 2025. https://doi.org/10.1109/TEMC.2024.3494021
crossref
14. J. Zhang, F. Kang, Z. Liu, Z. Qu, M. Xu, S. Zha, and et al, "Design of ultrawideband energy-selective surface based on triple-layer structure and semiconductor for HIRF protection," IEEE Transactions on Antennas and Propagation, vol. 73, no. 11, pp. 9619–9624, 2025. https://doi.org/10.1109/TAP.2025.3590600
crossref
15. L. Gai, Y. Xu, P. Liu, Z. He, and T. Zhou, "Design of a spatial multi-mode energy selective antenna integrating electromagnetic protection and anti-interference capabilities," IEEE Transactions on Antennas and Propagation, vol. 74, no. 4, pp. 3651–3656, 2026. https://doi.org/10.1109/TAP.2025.3648128
crossref
16. S. Zha, Z. Qu, J. Zhang, D. Zheng, and P. Liu, "A gain-reconfigurable reflector antenna with surface-mounted field-induced artificial magnetic conductor for adaptive HIRF prevention," IEEE Transactions on Antennas and Propagation, vol. 72, no. 9, pp. 7252–7260, 2024. https://doi.org/10.1109/TAP.2024.3434371
crossref

Biography

jees-2026-5-r-389f10.jpg
Sung-Sil Cho, https://orcid.org/0000-0003-0878-077X received the B.S. degree in information and communication engineering from Kongju National University, South Korea, in 2016, and the M.S. degree in information and communication engineering from Kongju National University, South Korea, in 2018. From March 2018 to February 2022, she was a Researcher with the Smart Natural Space Research Center, Kongju National University, South Korea. Since March 2022, she has been pursuing the Ph.D. degree in information and communication engineering at Kongju National University, South Korea. Her research interests include the design and applications of periodic electromagnetic structures.

Biography

jees-2026-5-r-389f11.jpg
Jong-Hwa Kwon, https://orcid.org/0000-0002-2132-7403 received the B.S. degree in electronics engineering from Chungnam National University, South Korea, in 1994, and the M.S. degree in radio science and engineering from Chungnam National University, South Korea, in 1999. He received the Ph.D. degree in electrical and electronic engineering from Yonsei University, South Korea, in 2010. From January 1999 to the present, he has been with the Electronics and Telecommunications Research Institute (ETRI), South Korea, where he is currently a Principal Researcher with the Radio Environment Monitoring Research Section, Radio Research Division, Broadcasting and Telecommunications Research Laboratory. He was a visiting researcher with Missouri University of Science and Technology, USA, from September 2021 to August 2022. He served as the Chair of the EMC Technology Research Committee of the Korean Institute of Electromagnetic Engineering and Science (KIEES) from 2017 to 2018, and as the Chair of the Electromagnetic Security Research Committee of KIEES from 2023 to 2024. His research interests include SI/PI and EMC countermeasure technologies and standardization, as well as high-power electromagnetic pulse (EMP) protection, measurement, and evaluation techniques.

Biography

jees-2026-5-r-389f12.jpg
Ic-Pyo Hong, https://orcid.org/0000-0003-1875-5420 received the B.S., M.S., and Ph.D. degrees in electronics engineering from Yonsei University, Seoul, South Korea, in 1994, 1996, and 2000, respectively. From 2000 to 2003, he was with the Information and Communication Division, Samsung Electronics Company, Suwon, South Korea, where he was a Senior Engineer with CDMA Mobile Research. He was a Visiting Scholar with Texas A&M University, College Station, TX, USA, in 2006, and Syracuse University, Syracuse, NY, USA, in 2012. Since 2003, he has been with the Department of Smart Information and Technology Engineering, Kongju National University, Cheonan, South Korea, where he is currently a Professor. His research interests include numerical techniques in electromagnetics and periodic electromagnetic structures.
TOOLS
Share :
Facebook Twitter Linked In Google+
METRICS Graph View
  • 0 Crossref
  • 0 Scopus
  • 1,177 View
  • 98 Download
Related articles in JEES

ABOUT
ARTICLE CATEGORY

Browse all articles >

BROWSE ARTICLES
AUTHOR INFORMATION
Editorial Office
101-1101 Lotte Castle President, 109 Mapo-daero, Mapo-gu, Seoul 04146, Republic of Korea
Tel: +82-2-337-9666    Fax: +82-2-711-7550    E-mail: admin-jees@kiees.or.kr                

Copyright © 2026 by The Korean Institute of Electromagnetic Engineering and Science.

Developed in M2PI

Close layer
prev next